Ongoing cleaning of your pump parts (shield set)

Ongoing cleaning of your pump parts

We recommend hand-washing your parts whenever possible. Frequently microwaving or running parts through the dishwasher will cause them to deteriorate faster, just as frequent sterilisation does. When cleaning, make sure parts are fully disassembled (e.g. membranes removed from valves, valves removed from breastshields, and backflow protectors taken apart).

Hand washing

To hand-wash parts in the sink, you’ll need a separate wash basin, a dedicated sponge or bottle brush, clean paper towels, standard dish soap, and access to warm, potable water.

  • Fill up a wash basin with warm, soapy water.
  • Add your pump parts and ‘swoosh’ them around.
  • Wash each part part thoroughly; be careful with the membranes.
  • Rinse thoroughly in cool water.
  • Set to air dry on a clean paper towel away from high traffic areas.
  • Allow to completely dry prior to assembling.

Dishwasher, microwave, and cleaning solutions

Spectra breastshields, bottles, and other hard plastic accessories are BPA-free and can go through the dishwasher without worry of harmful residue – however, it will cause them to wear down more quickly. You should hand wash whenever possible.

Do not wash silicone parts like valves, membranes, teats, and backflow protector membranes in the dishwasherThese parts are delicate and should be hand washed whenever possible.

For microwave steam cleaners or cleaning solutions (e.g. Milton's), follow the manufacturer’s instructions.

Pumping multiple times per day

If you’re pumping multiple times each day, you don’t have to wash your parts every time. Just put them in a sealed container like a snaplock bag and store them in the refrigerator between pumping sessions.

Note: This recommendation is assuming you have a healthy, full-term baby. For certain conditions your care provider might give alternative cleaning and sterilisation advise; always adhere to those. 

How to clean backflow protectors

You don’t need to clean your backflow protectors each time you use them. You only need to clean them if you see milk or moisture in them – don’t worry, this is completely normal and it means your backflow protectors have worked the way they should and protected your pump motor from harmful moisture. If you never see moisture in them, cleaning them every once in a while just to be safe is encouraged.

How to clean the tubing

The backflow protectors should prevent milk and condensation from entering the tubing, when working properly. If for some reason you’ve gotten milk or moisture in your tubing, there’s unfortunately no way to clean and sterilise it safely for future use. Tubing that has gotten wet needs to be replaced. That’s one reason why it’s really important to replace your backflow protectors regularly. Backflow protectors that have worn out can lose their moisture seal.

Sterilise before first time use

Before you use your breast pump for the first time, you’ll need to prepare by sterilising all parts that come in contact with your baby’s milk. This includes the breastshield, backflow protector, valve, bottle, bottle neck, sealing disc, bottle cap, and teat. Make sure you fully disassemble the backflow protectors, valve + membrane sets, and remove the valve from the breastshield prior to sterilisation. Do not sterilise the tubing or pump motor. Getting the tubing wet can cause irreparable damage to the motor and allow moisture into the motor, creating a cozy environment for mould, mildew and bacteria to grow.

Using boiling water to sterilise your breast pump parts

There are a few different methods you can use to sterilise your breast pump parts. We recommend the boiling water method.

  1. Select a pot large enough to fit all the parts without them rubbing together, such as a stock pot.
  2. Fill it with plenty of water to fully saturate the parts and leave plenty of room for a rolling boil. Make sure parts have plenty of room to move around and aren’t nestled together as this can cause irreparable warping.
  3. Place on a stovetop and bring to a rolling boil.
  4. Boil for 5 minutes, then remove from heat.
  5. Allow to cool to a manageable temperature, then use a a pair of tongues to carefully remove parts.
  6. Set them on a clean paper towel away from a high traffic area (don’t use a cloth towel as cloth can harbour bacteria).
  7. Allow to completely air dry prior to assembly.

Note: frequent sterilisation can cause your parts to deteriorate faster. If you follow a regular wash routine you shouldn’t need to sterilise more than just once. If your care provider has instructed you to sterilise your pump parts more frequently, you should do so. You may need to replace your parts more frequently.


Have more questions? Submit a request


Please sign in to leave a comment.
Powered by Zendesk